Audinate Dante-MY16-AUD User's Guide Page 54
- Page / 84
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Dante Controller User Guide
Copyright © 2014 Audinate Pty Ltd. All rights reserved.
-54-
Transmit Tab
The Transmit tab is used to inspect and modify the transmit configuration of a device.
The Transmit Tab is arranged in two areas:
n Transmit Channels: The area on the left pane of the tab shows the Tx channels for the device, and
any user-defined channel label. It allows you to create labels for transmit channels. Input to the table
is filtered to prevent illegal characters from being used in channel labels.
Supported devices will also show the following channel metering icons in the Signal column,
indicating the presence of audio on subscribed channels:
Channel is either muted, or receiving audio at less than -61dbFS
Channel is receiving audio between -61dbFS and 0dfFS
Channel is clipping
n Transmit Flows: The area on the right pane of the tab indicates how many unicast flows are cur-
rently in use, as well as the multicast transmit flows that have been configured on the device. Mult-
icast flows are listed in ID order, including the channels contained within the flow.
Note: Unicast flow details are not displayed in the transmit flow window. The total number of
transmit flows currently in use is shown at the top of the pane. The total number of flows is the sum of
- Dante Controller User 1
- Contents 2
- Contacts 7
- Software Licensing Notice 8
- About Audinate 9
- Introduction 10
- Dante Controller User Guide 11
- Previous releases 11
- Minimum System Requirements 12
- OperatingSystem Updates 13
- Firewall Configuration 13
- Monitor Requirements 13
- Installing Dante Controller 14
- Mac OS X 15
- Dante Basics 16
- Subscribing to Audio Channels 17
- Subscription Tooltips 17
- Routing Audio 19
- Subscription 20
- Redundancy 20
- Audio Formats 21
- Clock Synchronization 22
- LatencyMonitoring 23
- Dante Control and Monitoring 24
- Starting Dante Controller 25
- Using Dante Controller 29
- Menu bar 30
- Tool bar 31
- Status Bar 32
- Network View Tabs 32
- Device List Filtering 33
- Channel Groups 34
- Device Info 35
- Clock Status 36
- Clock Source 37
- Preferred Master 37
- Enable Sync To External 37
- About Clock Domains 38
- About Master Clocks 38
- Clock Status Monitoring 39
- Clock Status Monitor 40
- About Clock Offset 41
- About the Histogram 42
- Interpreting the Histogram 42
- Network Status 44
- Bandwidth Columns 45
- Latency Setting 45
- Latency Errors 45
- Packet Errors 45
- Filtering the Event List 46
- Clearing the Event List 46
- Saving the Event Log 47
- Automatic event logging 47
- Event Classification 47
- Failsafe mode 48
- Upgrade mode 48
- Device View 49
- Device View Tabs 51
- Receive Tab 52
- Available Channels 53
- Creating Subscriptions 53
- Transmit Tab 54
- Status Tab 55
- Dante Information 56
- Primary Interface 56
- Latency Tab 57
- Device Config Tab 60
- Configurable Parameters 61
- Network Config Tab 62
- Addresses 63
- HA Remote 64
- About Device Roles 67
- Saving Presets 68
- Applying Presets 69
- Preset Elements 70
- Preset Roles 70
- Automatic Assignments 71
- Target Devices 72
- Applying the Preset 73
- Global Configuration 73
- Troubleshooting 75
- Correct IP configuration 77
- Switch and Cabling Checklist 79
Related products and manuals for Audio cards Audinate Dante-MY16-AUD
(19 pages)ELEKTRO HELIOS TK7042 manuels
Manuels d'utilisation et guides de l'utilisateur pour Non ELEKTRO HELIOS TK7042.
Nous fournissons des manuels en pdf 6 ELEKTRO HELIOS TK7042 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comments to this Manuals